ADC Home > Reference Library > Technical Notes > Legacy Documents > Hardware & Drivers >

Legacy Documentclose button

Important: This document is part of the Legacy section of the ADC Reference Library. This information should not be used for new development.

Current information on this Reference Library topic can be found here:

AppleVision Technote

CONTENTS

This Technote describes some of the design features and characteristics of the AppleVision series of displays. It outlines information that is of interest to developers who may want to create cards and drivers for use with the AppleVision 1710, 1710AV, 850 and 850AV displays.

In October 1997, this Technote was revised to include information about the AppleVision 750 and 750 AV displays.



 Updated: [Feb 09 1998]






Guidelines for Card Developers

AppleVision displays support a number of possible resolutions and timing modes varying across a range of settings (rather than a discrete selection of modes and resolutions). As such, developers of display cards and drivers intending to be compatible with AppleVision monitors must adhere to the guidelines for implementing the cscGetConnection and cscGetModeTiming calls as documented in Chapter 11 of Designing PCI Cards and Drivers.

In general, software that adheres to the guidelines specified in Designing PCI Cards and Drivers (a.k.a. "Cards and Drivers") will be compatible with AppleVision displays. Guidelines of particular importance for compatibility with AppleVision displays are discussed below.

Never Cache Sense Codes

AppleVision monitors support the type 6 extended sense codes as described in the HW 30 - Sense Lines technote and on page 1-5 of the Display Device Driver Guide. In reading these sense codes from AppleVision displays, software should provide special support for the cscGetConnection call. Here, developers should always return the current sense information read from the display. This information should never be cached as it may be changed by the Display Manager over the ADB connection at any time--the sense information must be read on every call to cscGetConnection.

Report All Available Timing Modes

Video drivers should always report all of the timing modes that are supported by their graphics card including those timing modes supported by the card that are not apparently valid for the connected display. The Display Manager will calculate the intersection of the modes supported by the video driver and the modes supported by the display to determine the actual set of possible display modes.

Other Guidelines

  • You do not need to add new functional sResources.
  • Some drivers use the kAllModesValid or kAllModesSafe calls from scsGetConnection, rather than implementing cscGetModeTiming for all timings. If you add a group of invalid modes, you should not mark them as valid in the cscGetConnection call.
  • If your video card supports additional standard timings that do not have constants in Video.h, contact Apple Developer Support at feedback.
  • Support tagging. Tagging is part of the cscGetConnection call. It is documented in Chapter 11 of Designing PCI Cards and Drivers.
  • Trim duplicate timings. If your card has different display modes with the same timing and same number of pixels, you should trim all but one of the display modes for each timing mode.
  • Trim display modes that your hardware cannot support. For example, if your video card does not have enough VRAM to support a display mode, trim that display mode rather than marking it invalid. Such a display mode is not one that you would want an AppleVision display to enable.
  • Implement cscGetConnection and cscGetModeTiming for all timing modes. You should mark any timing mode that is not supported by the sense code as invalid and unsafe. When you do this, the display may override the decision.
  • Allow the display to switch to invalid timing modes. Some invalid timing modes may be validated by the display, and you should allow the switch, even though you may be unaware of their validity.
  • If you do not recognize a sense code, mark all timing modes invalid and program the hardware with the Apple 13" timing modes. This allows a smart display to come in as an unknown timing mode and enable the modes it supports.
  • If possible, framebuffer card vendors should test a configuration with two of their cards (in addition to built-in video and any other framebuffers) and at least one AppleVision display in that configuration. The AppleVision display must be driven by one of their two cards. They should be sure that Monitors and Sound correctly associates the AppleVision display with the correct video card and that the appropriate timings are available in the resolution panel (as opposed to just 640x480 @ 67 Hz).
  • When AppleVision displays are first powered up they always return the RGB 13" Type 6 sense code. Video drivers should avoid switching resolutions at any time during the boot process (even if the sense code appears to be invalid). The Display Manager will tell the video driver to switch to the correct mode at Finder launch time.

NuBus Guidelines

  • If your video card is intended to work on systems that were released before the Display Manager was introduced, you need to check for the Display Manager before enabling invalid timings. Otherwise, the user will see the invalid timings in the Monitors control panel.
  • Do not trim invalid functional sResources. If your video card does not have a programmable ROM, you will need to put the trimmed sResources back in when you patch your driver. These timing modes may be enabled by the display.

See Also: the "Graphics Drivers" chapter in Designing PCI Cards and Drivers.


Back to top

Available Display Modes

This section discusses information regarding the resolution, timing, and operational modes available for AppleVision displays.

Screen Resolutions

AppleVision 750 displays are adjusted at the factory for the following standard modes:

Mode

Pixel Resolution

Vertical Refresh

Horizontal Scan

VGA

640 x 480

60 Hz

31.5 kHz

Macintosh

640 x 480

66.67 Hz

34.97 kHz

VESA

800 x 600

60.31 Hz

37.9 kHz

VESA

800 x 600

75 Hz

46.9 kHz

Macintosh

832 x 624

74.55 Hz

49.7 kHz

Macintosh

1024 x 768

74.93 Hz

60.24 kHz

Macintosh

1152 x 870

75 Hz

68.7 kHz

VESA

1024 x 768

60 Hz

48.4 kHz

VESA

1280 x 1024

60 Hz

64.3 kHz

VESA

1280 x 1024

75.03 Hz

79.98 kHz



AppleVision 850 displays are adjusted at the factory for the following standard modes:

Mode

Pixel Resolution

Vertical Refresh

Horizontal Scan

VGA

640 x 480

60 Hz

31.469 kHz

Macintosh

640 x 480

67 Hz

35.036 kHz

VESA

640 x 480

72 Hz

37.861 kHz

VESA

640 x 480

75 Hz

37.500 kHz

VESA

640 x 480

85 Hz

43.269 kHz

VESA

800 x 600

56 Hz

35.160 kHz

VESA

800 x 600

60 Hz

37.879 kHz

VESA

800 x 600

72 Hz

48.077 kHz

VESA

800 x 600

75 Hz

46.875 kHz

VESA

800 x 600

85 Hz

53.674 kHz

Macintosh

832 x 624

75 Hz

49.700 kHz

IBM

1024 x 768

87 Hz interlaced

35.522 kHz interlaced

VESA

1024 x 768

60 Hz

48.363 kHz

VESA

1024 x 768

70 Hz

56.476 kHz

VESA

1024 x 768

75 Hz

60.023 kHz

VESA

1024 x 768

85 Hz

68.677 kHz

Macintosh

1152 x 870

75 Hz

68.700 kHz

VESA

1280 x 1024

75 Hz

79.976 kHz

VESA

1280 x 1024

85 Hz

91.146 kHz

VESA

1600 x 1200

75 Hz

93.750 kHz



AppleVision 1710 displays are adjusted at the factory for the following standard modes:

Mode

Pixel Resolution

Vertical Refresh

Horizontal Scan

VGA

640 x 480

60 Hz

31.5 kHz

Macintosh

640 x 480

66.67 Hz

34.97 kHz

VESA

800 x 600

60 Hz

37.9 kHz

VESA

800 x 600

75 Hz

46.9 kHz

Macintosh

832 x 624

74.55 Hz

49.700 kHz

Macintosh

1024 x 768

74.93 Hz

60.24 kHz

VESA

1024 x 768

60 Hz

48.4 kHz

VESA

1280 x 1024

60 Hz

64.3 kHz

VESA

1280 x 1024

75.03 Hz

79.98 kHz





Note:
AppleVision displays are not limited to the modes described by the above table: these new displays support any possible resolution that falls within the given timing range (see below).



Timing Modes

AppleVision displays are not limited to the timing modes listed in the above table. AppleVision 850 displays will synchronize over timing ranges 48-120 Hz for vertical refresh, and 30-94 kHz for horizontal scan; and, AppleVision 1710 and 750 displays will synchronize over timing ranges 40-120 Hz for vertical refresh, and 30-80 kHz for horizontal scan.

Operating Modes

AppleVision displays have a feature that allows them to work in two different modes, depending on whether or not the AppleVision software is present. These modes are Remote and Local.

When the display is first powered up, it is in Local mode. If it is connected to a PC-compatible computer, it remains in Local mode. If it is connected to a Macintosh computer, but the Macintosh AppleVision software is not installed, it also remains in Local mode. If the display is connected to a Macintosh computer with the AppleVision software installed, the software puts the display into Remote mode by sending a series of ADB messages to the display. The display then remains in Remote mode.

In Local mode, the computer does not control the display. When the user presses control buttons on the front of the display, the display handles these actions and makes the required changes to its settings. In addition, when one of the video front panel buttons is pressed, the on-screen display (OSD) appears to provide visual feedback on the changes being made.

Remote mode allows the Monitors and Sound control panel to control the settings of the display. In addition, the OSD does not appear on the screen. Instead, when any front panel buttons are pressed, the information about which button was pressed is sent to the Macintosh over the ADB cable. The Display Manager sends instructions to the display for changing its settings.


Back to top

Display Data Channel (DDC) Support

The AppleVision 1710, 750 and 850 displays implement both DDC1 and DDC2B standards (for cross platform compatibility) through a scheme compatible with the older Macintosh sense-code-detection mechanism as described in the following documents:

Technote HW08, "Color Monitor Connections"

Technote HW30, "Sense Lines"

Further information regarding the DDC standard is available from:

Video Electronics and Standards Association (VESA)
2150 North First Street, Suite 440
San Jose, CA. 95131-2029
Phone: (408) 435-0333
Fax: (408)435-8225
<http://www.vesa.org>
ftp.vesa.org


Back to top

Operational Requirements

This section provides information regarding environmental and power requirements for operation of an AppleVision monitor.

AppleVision 750 Environmental and Power Requirements

Temperature

10° to 40° C (50° to 104° F) -- operating
0° to 60° C (32° to 140° F) -- storage
-40° to 60° C (-4° to 140° F) -- shipping

Relative humidity

10% to 80% non condensing -- operating
5% to 90% non condensing -- storage
5% to 90% non condensing -- shipping

Operating altitude

0 to 10,000 feet (0 to 3048 meters)

Shipping altitude

0 to 35,000 feet (0 to 10,670 meters)

AC input range

100-240 volts AC, auto select

AC input Frequency range

50-60 Hz, single phase

AppleVision 850 Environmental and Power Requirements

Temperature

10° to 40° C (50° to 104° F) -- operating
0° to 60° C (32° to 140° F) -- storage
-40° to 60° C (-4° to 140° F) -- shipping

Relative humidity

20% to 95% non condensing -- operating
5% to 95% non condensing -- storage
5% to 95% non condensing -- shipping

Operating altitude

0 to 10,000 feet (0 to 3048 meters)

Shipping altitude

0 to 35,000 feet (0 to 10,670 meters)

AC input range

90-264 volts AC, auto select

AC input Frequency range

47-63 Hz, single phase


AppleVision 1710 Environmental and Power Requirements

Temperature

10° to 40° C (50° to 104° F) -- operating
0° to 60° C (32° to 140° F) -- storage
-40° to 60° C (-4° to 140° F) -- shipping

Relative humidity

10% to 80% non condensing -- operating
5% to 90% non condensing -- storage
5% to 95% non condensing -- shipping

Operating altitude

0 to 10,000 feet (0 to 3048 meters)

Shipping altitude

0 to 35,000 feet (0 to 10,670 meters)

AC input range

90-264 volts AC, auto select

AC input Frequency range

47-63 Hz, single phase



Back to top

Hardware Interfaces

This section describes the hardware interface for the AppleVision 1710, 750 and 850 Displays. Both displays provide an interface for the video connector and the ADB ports and connector. The AppleVision 1710AV, 750AV and 850AV displays also provide an interface for the sound input port and the sound output port.


Back to top

Video Port and Connector

The video port connection is made through a standard DB-15 connector. AppleVision 850, 750 and 1710 displays define pin 8 in different ways as shown in the following tables:

850 Pin Assignments

AppleVision 850 Connector Pin Assignments



Pin

Output Signal

Pin

Output Signal

1

Red video ground

9

Blue video

2

Red video

10

ID 3 or DDC SDA

3

Not used

11

Vertical Sync return

4

ID 1 or DDC return

12

Vertical Sync

5

Green video

13

Blue video ground

6

Green video ground

14

Horizontal Sync return

7

ID 2 or DDC SCL

15

Horizontal Sync

8

DDC 5V

Shell

Shield ground



1710 Pin Assignments

AppleVision 1710 and 750 Connector Pin Assignments



Pin

Output Signal

Pin

Output Signal

1

Red video ground

9

Blue video

2

Red video

10

ID 3 or DDC SDA

3

Not used

11

Vertical Sync return

4

ID 1 or DDC return

12

Vertical Sync

5

Green video

13

Blue video ground

6

Green video ground

14

Horizontal Sync return

7

ID 2 or DDC SCL

15

Horizontal Sync

8

Not Used

Shell

Shield ground



Abbreviations used in the above tables:

  • ID -- Identification
  • DDC -- Display Data Channel
  • SCL -- Serial Clock
  • SDA -- Serial Data


Note:
In the past, graphics drivers sensed the type of display attached to the video card by means of three sense lines on the video cable (ID 1, ID 2, and ID 3). These lines were encoded to produce a hardware sense code algorithm. This has changed for AppleVision displays and while the display is operating in local mode, these sense lines may return different sense codes depending on the display's current resolution and timing configuration.




Back to top

ADB Port and Connector

The ADB port is only used in conjunction with Mac OS compatible computers and provides facilities for operation of the display in the remote operating mode allowing for software configuration of the display over the ADB connection. The ADB connection is used to transfer both audio and video control data between the Mac OS compatible computer and the display. The AppleVision 1710, 750 and the 850 displays have an ADB port on both side panels. These ports allow you to connect a mouse or keyboard directly to the display.  

ADB pins

ADB Connector Pin Assignments



Pin

Signal Name

Description

1

ADB

Bidirectional data bus for input and output; transfers audio (AV display only) and video control data between the CPU and the display

2

POWER ON

Enables power to be turned on from the keyboard

3

+5VDC

+5 V power

4

GND

Logic Ground

Shield

None

Chassis Ground





Note:
For multiple monitor support, a shielded ADB splitter (part number 590-0448) is available.




Back to top

Sound Ports and Adapter

The sound ports are found only on the AppleVision 1710AV, 750AV and on the 850AV Displays. The sound output port is used for headphones or external speakers. The sound input port accepts sound inputs from a microphone or any appropriate sound source. These ports are both stereo ports, but they use single ministereo audio connectors. You must make sure that the connector you use for audio input or output is compatible with your sound equipment. For example, if you are connecting to a device that uses dual (RCA-type) connectors for stereo sound, use a "Y" adapter to connect the stereo ports of the sound source or speakers to the display's single-connector stereo port. Figure 2-4 shows the sound adapter configuration.

The AppleVision 1710AV, 750AV and 850AV Displays also have the following sound ports:

  • A sound input port, on the left panel, allows you to connect an external microphone or other sound source to the display
  • A sound output port, on the right panel, allows you to connect speakers or headphones to the display

Back to top

Compatibility Requirements

This section provides information regarding what Apple computers are compatible with the AppleVision display, video cards, and versions of the Mac OS that support AppleVision displays.

CPU configurations supporting the AppleVision display

The following Apple CPUs are compatible with AppleVision displays:

  • PCI-based CPU's including
    • 7200/90/100/120
    • 7500/100/120
    • 7600/120
    • 8500/120/132/150
    • 9500/120/132/150
    • 7300/8600/9600/5500/6500

    All PCI-based machines shipping a the time of this document's publication are supported.

  • PowerMac CPU's including
    • 8100/80/100/110
    • 8100/80/100/110AV
    • 7100/66/80, the 6100/66
    • 6100/60AV
    • 6200
    • 6300 models



  • PowerBooks CPU's including
    • 280/280c/2300 (with Mini Dock/Duo Dock II)
    • 520/520c
    • 540/540c
    • 5xx/PowerMac Upgrade
    • 5300
    • 1400
    • 3400 series



  • Quadra CPU's including
    • Quadra 605
    • Quadra 610
    • Quadra 630
    • Quadra 630/PowerMac Upgrade
    • Centris 650
    • Quadra 650
    • Quadra 650/PowerMac Upgrade
    • Quadra 950
    • Quadra 900
    • Quadra 950/PowerMac Upgrade
    • Quadra 660AV
    • Quadra 840AV



  • Apple DOS Compatible CPU's
    • Quadra 610/DOS
    • 6100/DOS
    • 640 DOS
    • 90MHz 586
    • 100MHz Pentium
    • 166 MHz Pentium PC cards for PCI CPUs

Video Card Compatibility

In addition to the on-board video provided by the CPUs listed in Table 1-4, plug-in video cards, such as the NuBus 24AC video card, also support AppleVision displays.

Apple video cards 8.24, 8.24GC, and 4.8 do not support the AppleVision displays. In addition, plug-in video cards that do follow the new guidelines defined in the "Graphics Drivers" section of Designing PCI Cards and Drivers for Macintosh Computers do not support the displays.

Operating System Compatibility

You should use System 7.5 or later with the AppleVision display. If you run earlier versions of the operating system, QuickTime delays the loading of the AppleVision INIT. You may have renamed AppleVision INIT with a name that begins with a letter later than Q (QuickTime). This means that the INIT installs after QuickTime, and QuickTime moves the AppleVision components, delaying booting.


Back to top

References

"Graphics Drivers" chapter in Designing PCI Cards and Drivers.

Display Device Driver Guide

Technote HW08, "Color Monitor Connections"

Technote HW30, "Sense Lines"



Back to top


Downloadables

Acrobat

Acrobat version of this Note (116K).

Download




Back to top


Did this document help you?
Yes: Tell us what works for you.
It’s good, but: Report typos, inaccuracies, and so forth.
It wasn’t helpful: Tell us what would have helped.