Net::Config(3pm) Perl Programmers Reference Guide Net::Config(3pm)
NAME
Net::Config - Local configuration data for libnet
SYNOPSYS
use Net::Config qw(%NetConfig);
DESCRIPTION
"Net::Config" holds configuration data for the modules in the libnet distribuion. During installation
you will be asked for these values.
The configuration data is held globally in a file in the perl installation tree, but a user may over-ride override
ride any of these values by providing their own. This can be done by having a ".libnetrc" file in
their home directory. This file should return a reference to a HASH containing the keys described
below. For example
# .libnetrc
{
nntp_hosts => [ "my_prefered_host" ],
ph_hosts => [ "my_ph_server" ],
}
__END__
METHODS
"Net::Config" defines the following methods. They are methods as they are invoked as class methods.
This is because "Net::Config" inherits from "Net::LocalCfg" so you can override these methods if you
want.
requires_firewall HOST
Attempts to determine if a given host is outside your firewall. Possible return values are.
-1 Cannot lookup hostname
0 Host is inside firewall (or there is no ftp_firewall entry)
1 Host is outside the firewall
This is done by using hostname lookup and the "local_netmask" entry in the configuration data.
NetConfig VALUES
nntp_hosts
snpp_hosts
pop3_hosts
smtp_hosts
ph_hosts
daytime_hosts
time_hosts
Each is a reference to an array of hostnames (in order of preference), which should be used for
the given protocol
inet_domain
Your internet domain name
ftp_firewall
If you have an FTP proxy firewall (NOT an HTTP or SOCKS firewall) then this value should be set
to the firewall hostname. If your firewall does not listen to port 21, then this value should be
set to "hostname:port" (eg "hostname:99")
ftp_firewall_type
There are many different ftp firewall products available. But unfortunately there is no standard
for how to traverse a firewall. The list below shows the sequence of commands that Net::FTP will
use
user Username for remote host
pass Password for remote host
fwuser Username for firewall
fwpass Password for firewall
remote.host The hostname of the remote ftp server
0 There is no firewall
1
USER user@remote.host
PASS pass
2
USER fwuser
PASS fwpass
USER user@remote.host
PASS pass
3
USER fwuser
PASS fwpass
SITE remote.site
USER user
PASS pass
4
USER fwuser
PASS fwpass
OPEN remote.site
USER user
PASS pass
5
USER user@fwuser@remote.site
PASS pass@fwpass
6
USER fwuser@remote.site
PASS fwpass
USER user
PASS pass
7
USER user@remote.host
PASS pass
AUTH fwuser
RESP fwpass
ftp_ext_passive
ftp_int_pasive
FTP servers normally work on a non-passive mode. That is when you want to transfer data you have
to tell the server the address and port to connect to.
With some firewalls this does not work as the server cannot connect to your machine (because you
are behind a firewall) and the firewall does not re-write the command. In this case you should
set "ftp_ext_passive" to a true value.
Some servers are configured to only work in passive mode. If you have one of these you can force
"Net::FTP" to always transfer in passive mode; when not going via a firewall, by setting
"ftp_int_passive" to a true value.
local_netmask
A reference to a list of netmask strings in the form "134.99.4.0/24". These are used by the
"requires_firewall" function to determine if a given host is inside or outside your firewall.
The following entries are used during installation & testing on the libnet package
test_hosts
If true then "make test" may attempt to connect to hosts given in the configuration.
test_exists
If true then "Configure" will check each hostname given that it exists
$Id: //depot/libnet/Net/Config.pm#17 $
perl v5.8.8 2001-09-21 Net::Config(3pm)
|