NTPDC(8) BSD System Manager's Manual NTPDC(8)
NAME
ntpdc -- special NTP query program
SYNOPSIS
ntpdc [-ilnps] [-c command] [host ...]
DESCRIPTION
The ntpdc utility is used to query the ntpd(8) daemon about its current state and to request changes in
that state. The program may be run either in interactive mode or controlled using command line argu-ments. arguments.
ments. Extensive state and statistics information is available through the ntpdc interface. In addi-tion, addition,
tion, nearly all the configuration options which can be specified at startup using ntpd's configuration
file may also be specified at run time using ntpdc.
The following options are available:
-c command
The following argument is interpreted as an interactive format command and is added to the list
of commands to be executed on the specified host(s). Multiple -c options may be given.
-i Force ntpdc to operate in interactive mode. Prompts will be written to the standard output and
commands read from the standard input.
-l Obtain a list of peers which are known to the server(s). This switch is equivalent to `-c
listpeers'.
-n Output all host addresses in dotted-quad numeric format rather than converting to the canonical
host names.
-p Print a list of the peers known to the server as well as a summary of their state. This is
equivalent to `-c peers'.
-s Print a list of the peers known to the server as well as a summary of their state, but in a
slightly different format than the -p switch. This is equivalent to `-c dmpeers'.
If one or more request options are included on the command line when ntpdc is executed, each of the
requests will be sent to the NTP servers running on each of the hosts given as command line arguments,
or on localhost by default. If no request options are given, ntpdc will attempt to read commands from
the standard input and execute these on the NTP server running on the first host given on the command
line, again defaulting to localhost when no other host is specified. The ntpdc utility will prompt for
commands if the standard input is a terminal device.
The ntpdc utility uses NTP mode 7 packets to communicate with the NTP server, and hence can be used to
query any compatible server on the network which permits it. Note that since NTP is a UDP protocol
this communication will be somewhat unreliable, especially over large distances in terms of network
topology. The ntpdc utility makes no attempt to retransmit requests, and will time requests out if the
remote host is not heard from within a suitable timeout time.
The operation of ntpdc are specific to the particular implementation of the ntpd(8) daemon and can be
expected to work only with this and maybe some previous versions of the daemon. Requests from a remote
ntpdc utility which affect the state of the local server must be authenticated, which requires both the
remote program and local server share a common key and key identifier. Specifying a command line
option other than -i or -n will cause the specified query (queries) to be sent to the indicated host(s)
immediately. Otherwise, ntpdc will attempt to read interactive format commands from the standard
input.
Interactive Commands
Interactive format commands consist of a keyword followed by zero to four arguments. Only enough char-acters characters
acters of the full keyword to uniquely identify the command need be typed. The output of a command is
normally sent to the standard output, but optionally the output of individual commands may be sent to a
file by appending a `>', followed by a file name, to the command line.
A number of interactive format commands are executed entirely within the ntpdc utility itself and do
not result in NTP mode 7 requests being sent to a server. These are described following.
? command_keyword
help command_keyword
A ? will print a list of all the command keywords known to this incarnation of ntpdc. A ? fol-lowed followed
lowed by a command keyword will print function and usage information about the command. This
command is probably a better source of information about ntpq(8) than this manual page.
delay milliseconds
Specify a time interval to be added to timestamps included in requests which require authenti-cation. authentication.
cation. This is used to enable (unreliable) server reconfiguration over long delay network
paths or between machines whose clocks are unsynchronized. Actually the server does not now
require timestamps in authenticated requests, so this command may be obsolete.
host hostname
Set the host to which future queries will be sent. Hostname may be either a host name or a
numeric address.
hostnames [yes | no]
If yes is specified, host names are printed in information displays. If no is specified,
numeric addresses are printed instead. The default is yes, unless modified using the command
line -n switch.
keyid keyid
This command allows the specification of a key number to be used to authenticate configuration
requests. This must correspond to a key number the server has been configured to use for this
purpose.
quit Exit ntpdc.
passwd This command prompts you to type in a password (which will not be echoed) which will be used to
authenticate configuration requests. The password must correspond to the key configured for
use by the NTP server for this purpose if such requests are to be successful.
timeout milliseconds
Specify a timeout period for responses to server queries. The default is about 8000 millisec-onds. milliseconds.
onds. Note that since ntpdc retries each query once after a timeout, the total waiting time
for a timeout will be twice the timeout value set.
Control Message Commands
Query commands result in NTP mode 7 packets containing requests for information being sent to the
server. These are read-only commands in that they make no modification of the server configuration
state.
listpeers
Obtains and prints a brief list of the peers for which the server is maintaining state. These
should include all configured peer associations as well as those peers whose stratum is such
that they are considered by the server to be possible future synchonization candidates.
peers Obtains a list of peers for which the server is maintaining state, along with a summary of that
state. Summary information includes the address of the remote peer, the local interface
address (0.0.0.0 if a local address has yet to be determined), the stratum of the remote peer
(a stratum of 16 indicates the remote peer is unsynchronized), the polling interval, in sec-onds, seconds,
onds, the reachability register, in octal, and the current estimated delay, offset and disper-sion dispersion
sion of the peer, all in seconds.
The character in the left margin indicates the mode this peer entry is operating in. A `+'
denotes symmetric active, a `-' indicates symmetric passive, a `=' means the remote server is
being polled in client mode, a `^' indicates that the server is broadcasting to this address, a
`~' denotes that the remote peer is sending broadcasts and a `*' marks the peer the server is
currently synchronizing to.
The contents of the host field may be one of four forms. It may be a host name, an IP address,
a reference clock implementation name with its parameter or REFCLK(implementation_number,
parameter). On hostnames no only IP-addresses will be displayed.
dmpeers
A slightly different peer summary list. Identical to the output of the peers command, except
for the character in the leftmost column. Characters only appear beside peers which were
included in the final stage of the clock selection algorithm. A `.' indicates that this peer
was cast off in the falseticker detection, while a `+' indicates that the peer made it through.
A `*' denotes the peer the server is currently synchronizing with.
showpeer peer_address ...
Shows a detailed display of the current peer variables for one or more peers. Most of these
values are described in the NTP Version 2 specification.
pstats peer_address ...
Show per-peer statistic counters associated with the specified peer(s).
clockinfo clock_peer_address ...
Obtain and print information concerning a peer clock. The values obtained provide information
on the setting of fudge factors and other clock performance information.
kerninfo
Obtain and print kernel phase-lock loop operating parameters. This information is available
only if the kernel has been specially modified for a precision timekeeping function.
loopinfo [oneline | multiline]
Print the values of selected loop filter variables. The loop filter is the part of NTP which
deals with adjusting the local system clock. The `offset' is the last offset given to the loop
filter by the packet processing code. The `frequency' is the frequency error of the local
clock in parts-per-million (ppm). The `time_const' controls the stiffness of the phase-lock
loop and thus the speed at which it can adapt to oscillator drift. The `watchdog timer' value
is the number of seconds which have elapsed since the last sample offset was given to the loop
filter. The oneline and multiline options specify the format in which this information is to
be printed, with multiline as the default.
sysinfo
Print a variety of system state variables, i.e., state related to the local server. All except
the last four lines are described in the NTP Version 3 specification, RFC-1305.
The `system flags' show various system flags, some of which can be set and cleared by the
enable and disable configuration commands, respectively. These are the auth, bclient, monitor,
pll, pps and stats flags. See the ntpd(8) documentation for the meaning of these flags. There
are two additional flags which are read only, the kernel_pll and kernel_pps. These flags indi-cate indicate
cate the synchronization status when the precision time kernel modifications are in use. The
`kernel_pll' indicates that the local clock is being disciplined by the kernel, while the
`kernel_pps' indicates the kernel discipline is provided by the PPS signal.
The `stability' is the residual frequency error remaining after the system frequency correction
is applied and is intended for maintenance and debugging. In most architectures, this value
will initially decrease from as high as 500 ppm to a nominal value in the range .01 to 0.1 ppm.
If it remains high for some time after starting the daemon, something may be wrong with the
local clock, or the value of the kernel variable kern.clockrate.tick may be incorrect.
The `broadcastdelay' shows the default broadcast delay, as set by the broadcastdelay configura-tion configuration
tion command.
The `authdelay' shows the default authentication delay, as set by the authdelay configuration
command.
sysstats
Print statistics counters maintained in the protocol module.
memstats
Print statistics counters related to memory allocation code.
iostats
Print statistics counters maintained in the input-output module.
timerstats
Print statistics counters maintained in the timer/event queue support code.
reslist
Obtain and print the server's restriction list. This list is (usually) printed in sorted order
and may help to understand how the restrictions are applied.
monlist [version]
Obtain and print traffic counts collected and maintained by the monitor facility. The version
number should not normally need to be specified.
clkbug clock_peer_address ...
Obtain debugging information for a reference clock driver. This information is provided only
by some clock drivers and is mostly undecodable without a copy of the driver source in hand.
Runtime Configuration Requests
All requests which cause state changes in the server are authenticated by the server using a configured
NTP key (the facility can also be disabled by the server by not configuring a key). The key number and
the corresponding key must also be made known to ntpdc. This can be done using the keyid and passwd
commands, the latter of which will prompt at the terminal for a password to use as the encryption key.
You will also be prompted automatically for both the key number and password the first time a command
which would result in an authenticated request to the server is given. Authentication not only pro-vides provides
vides verification that the requester has permission to make such changes, but also gives an extra
degree of protection again transmission errors.
Authenticated requests always include a timestamp in the packet data, which is included in the computa-tion computation
tion of the authentication code. This timestamp is compared by the server to its receive time stamp.
If they differ by more than a small amount the request is rejected. This is done for two reasons.
First, it makes simple replay attacks on the server, by someone who might be able to overhear traffic
on your LAN, much more difficult. Second, it makes it more difficult to request configuration changes
to your server from topologically remote hosts. While the reconfiguration facility will work well with
a server on the local host, and may work adequately between time-synchronized hosts on the same LAN, it
will work very poorly for more distant hosts. As such, if reasonable passwords are chosen, care is
taken in the distribution and protection of keys and appropriate source address restrictions are
applied, the run time reconfiguration facility should provide an adequate level of security.
The following commands all make authenticated requests.
addpeer peer_address [keyid] [version] [prefer]
Add a configured peer association at the given address and operating in symmetric active mode.
Note that an existing association with the same peer may be deleted when this command is exe-cuted, executed,
cuted, or may simply be converted to conform to the new configuration, as appropriate. If the
optional keyid is a nonzero integer, all outgoing packets to the remote server will have an
authentication field attached encrypted with this key. If the value is 0 (or not given) no
authentication will be done. The version can be 1, 2 or 3 and defaults to 3. The prefer key-word keyword
word indicates a preferred peer (and thus will be used primarily for clock synchronisation if
possible). The preferred peer also determines the validity of the PPS signal - if the pre-ferred preferred
ferred peer is suitable for synchronisation so is the PPS signal.
addserver peer_address [keyid] [version] [prefer]
Identical to the addpeer command, except that the operating mode is client.
broadcast peer_address [keyid] [version] [prefer]
Identical to the addpeer command, except that the operating mode is broadcast. In this case a
valid key identifier and key are required. The peer_address parameter can be the broadcast
address of the local network or a multicast group address assigned to NTP. If a multicast
address, a multicast-capable kernel is required.
unconfig peer_address ...
This command causes the configured bit to be removed from the specified peer(s). In many cases
this will cause the peer association to be deleted. When appropriate, however, the association
may persist in an unconfigured mode if the remote peer is willing to continue on in this fash-ion. fashion.
ion.
fudge peer_address [time1] [time2] [stratum] [refid]
This command provides a way to set certain data for a reference clock. See the source listing
for further information.
enable flag ...
disable flag ...
These commands operate in the same way as the enable and disable configuration file commands of
ntpd(8). Following is a description of the flags. Note that only the auth, bclient, monitor,
pll, pps and stats flags can be set by ntpdc; the pll_kernel and pps_kernel flags are read-only. readonly.
only.
auth Enables the server to synchronize with unconfigured peers only if the peer has been
correctly authenticated using a trusted key and key identifier. The default for this
flag is enable.
bclient
Enables the server to listen for a message from a broadcast or multicast server, as in
the multicastclient command with default address. The default for this flag is dis-able. disable.
able.
monitor
Enables the monitoring facility. See the monlist command for further information. The
default for this flag is enable.
pll Enables the server to adjust its local clock by means of NTP. If disabled, the local
clock free-runs at its intrinsic time and frequency offset. This flag is useful in
case the local clock is controlled by some other device or protocol and NTP is used
only to provide synchronization to other clients. In this case, the local clock driver
is used. See the "Reference Clock Drivers" page (available as part of the HTML docu-mentation documentation
mentation provided in /usr/share/doc/ntp) page for further information. The default
for this flag is enable.
pps Enables the pulse-per-second (PPS) signal when frequency and time is disciplined by the
precision time kernel modifications. See the "A Kernel Model for Precision
Timekeeping" page for further information. The default for this flag is disable.
stats Enables the statistics facility. See the Monitoring Options section of the ntp.conf(5)
page for further information. The default for this flag is enable.
pll_kernel
When the precision time kernel modifications are installed, this indicates the kernel
controls the clock discipline; otherwise, the daemon controls the clock discipline.
pps_kernel
When the precision time kernel modifications are installed and a pulse-per-second (PPS)
signal is available, this indicates the PPS signal controls the clock discipline; oth-erwise, otherwise,
erwise, the daemon or kernel controls the clock discipline, as indicated by the
pll_kernel flag.
restrict address mask flag ...
This command operates in the same way as the restrict configuration file commands of ntpd(8).
unrestrict address mask flag ...
Unrestrict the matching entry from the restrict list.
delrestrict address mask [ntpport]
Delete the matching entry from the restrict list.
readkeys
Causes the current set of authentication keys to be purged and a new set to be obtained by
rereading the keys file (which must have been specified in the ntpd(8) configuration file).
This allows encryption keys to be changed without restarting the server.
trustedkey keyid ...
untrustedkey keyid ...
These commands operate in the same way as the trustedkey and untrustedkey configuration file
commands of ntpd(8).
authinfo
Returns information concerning the authentication module, including known keys and counts of
encryptions and decryptions which have been done.
traps Display the traps set in the server. See the source listing for further information.
addtrap address [port] [interface]
Set a trap for asynchronous messages. See the source listing for further information.
clrtrap address [port] [interface]
Clear a trap for asynchronous messages. See the source listing for further information.
reset Clear the statistics counters in various modules of the server. See the source listing for
further information.
SEE ALSO
ntp.conf(5), ntpd(8)
David L. Mills, Network Time Protocol (Version 3), RFC1305.
BUGS
The ntpdc utility is a crude hack. Much of the information it shows is deadly boring and could only be
loved by its implementer. The program was designed so that new (and temporary) features were easy to
hack in, at great expense to the program's ease of use. Despite this, the program is occasionally use-ful. useful.
ful.
BSD January 7, 2000 BSD
|